Go back to PatrolBase.co.uk

EVOLVE your Airsoft gun today!

There's a new MOSFET in town! A complete drop-in placement for your Airsoft version 2 gearbox which now includes the possibility of ramping! More on that later...

What is this new bit of kit exactly? We're proud to be stocking a complete trigger board replacement with built-in sector gear cam detection and microswitch trigger switch which provides up to 12x adjustable features.

Within a couple of minutes after splitting your Version 2 gearbox in half, say goodbye to your cut off lever, anti reversal latch and secure your new trigger board with one screw. You've now eliminated cut off lever wear (where your gun would fire full auto even on semi), no more backspin of your gears thanks for programmable active breaking and you have fresh 16 gauge stiff fitting wiring throughout your build.

Below is a basic installation video, the video covers more than just the ETS III unit installation but the guidance is the same.

Something else new for a MOSFET / Trigger Board replacement that we have never seen before, every unit gets shipped from the manufacturer in its own mini foam-filled polymer hard case! Your electronics are protected from day one and make for a very nice storage box for keepsake after you have fitted your unit.

Let's get onto some of those features that make this MOSFET truly worth the price tag!

Programable eatures:

  • Semi-auto programming features:
    • Burst control from 1 to 10 shots per trigger pull
    • Adjustable trigger response up-to 10x levels of sensitivity
    • Ramping - Switch from semi to progressive auto-firing after a programmed hold time
    • Active breaking milliseconds control from 10 to 50 milliseconds for fine pre-cocking tuning
    • Full cycle resets your piston to the front of every trigger pull for more realistic firing and prevents spring tension wear
    • Reset - Resets all modified settings back to factory default
  • Full auto programming features:
    • Burst control when flicked to full-auto from 1 to 10x shots per trigger pull
    • PWM ROF control - Literally controls your rate of fire up to 4-speed changes
    • Ramping auto - If you previously have a burst control limit on your full auto switch, press and hold on full auto will override after the burst is performed and go straight into constant full-auto firing
    • Battery protection up to 5x levels of sensitivity. You will receive a buzz after shooting warning you that you're running low on juice before cutting the power completely
    • Full cycle saves spring wear and completes a full operation and piston reset no matter how long you hold full auto for
    • Reset - Resets all modified settings back to factory default

Below is a very detailed video on how to program the new MOSFET. Within the included product hard case is a simplified paper guide too:

What else is so good about this system? Well, there are no optical sensors that could get covered up in your gear grease, your switches are micro but mechanical and are adjustable in sensitivity as shown above. The unit can also handle up to 30v, but we do recommend a maximum of 14v. As well as handling the crazy high voltage, high-speed gears and high torque setups you can easily modify the wiring or re-solder to go from rear to front wired in a couple of minutes (this would void your warranty).

To find out more about the product features and additional product photos, you can check it all out here on our official product page.

Written by Karl, who has written a total of 202 posts.

Posted in Patrol Base News | 2 Comments

2 thoughts on “EVOLVE your Airsoft gun today!”

  1. david

    i have gust instaled it on my gun and i went to do the settings when i went throw the settings i went to burst on semi and did the clicks but then but when i put it in semi i expected a short burst but it went full auto for a good 10 seconds so then i unpuluged the battary and it all stopped which was exspeded and i did it again on on another setting and it did the same and i need to know what is wroung with it we


Leave a Reply

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>


Back to top